Call on: +91-9892171042

Super Alloys Rene 41, AISI 683 AMS 5545 AMS 5712 AMS 5713 AMS 5800 DIN 2.4973 GE B50T44 GE B50T59 GE B50T94 GE B50TF109 GE B50TF11 GE B50TF110 GE B50TF210 GE B50TF59 GE B50TF75 GE B50TF76 UNS N07041

Super Alloys


  • Super Alloys Rene 41 is available in strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves.

    Super Alloys Rene 41 is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened.

  • Super Alloys Rene 41 Chemical Data


    Aluminum 0.2 - 0.8
    Boron 0.006 max
    Carbon 0.08 max
    Chromium 17 - 21
    Cobalt 1 max
    Copper 0.3 max
    Iron Balance
    Manganese 0.35 max
    Molybdenum 2.8 - 3.3
    Nickel 50 - 55
    Niobium 4.75 - 5.5
    Phosphorus 0.015 max
    Silicon 0.35 max
    Sulphur 0.015 max
    Titanium 0.65 - 1.15
    Principal Design Features This is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened.
    Super Alloys Rene 41 Applications Applications include gas turbine hot section components and cryogenic storage tanks.
    Super Alloys Rene 41 Machinability Conventional machining techniques used for iron based alloys may be used. This alloy does work-harden during machining and has higher strength and "gumminess" not typical of steels. Heavy duty machining equipment and tooling should be used to minimize chatter or work-hardening of the alloy ahead of the cutting. Most any commercial coolant may be used in the machining operations. Water-base coolants are preferred for high speed operations such as turning, grinding, or milling. Heavy lubricants work best for drilling, tapping, broaching or boring. Turning: Carbide tools are recommended for turning with a continuous cut. High-speed steel tooling should be used for interrupted cuts and for smooth finishing to close tolerance. Tools should have a positive rake angle. Cutting speeds and feeds are in the following ranges: Drilling: Steady feed rates must be used to avoid work hardening due to dwelling of the drill on the metal. Rigid set-ups are essential with as short a stub drill as feasible. Heavy-duty, high-speed steel drills with a heavy web are recommended. Feeds vary from 0.0007 inch per rev. for holes of less than 1/16" diameter, 0.003 inch per rev. for 1/4" dia., to 0.010 inch per rev. for holes of 7/8"diameter. Slow surface speed, as 8-10 feet/minute, are best for drilling. Milling: To obtain good accuracy and a smooth finish it is essential to have rigid machines and fixtures and sharp cutting tools. High-speed steel cutters such as M-2 or M-10 work best with cutting speeds of 5 to 15 feet per minute and feed of 0.001"-0.004" per cutting tooth. Grinding: The alloy should be wet ground and aluminum oxide wheels or belts are preferred.
    Super Alloys Rene 41 Forming This alloy has good ductility and may be readily formed by all conventional methods. Because the alloy is stronger than regular steel it requires more powerful equipment to accomplish forming. Heavy-duty lubricants should be used during cold forming. It is essential to thoroughly clean the part of all traces of lubricant after forming as embrittlement of the alloy may occur at high temperatures if lubricant is left on.
    Super Alloys Rene 41 Welding The commonly used welding methods work well with this alloy. Matching alloy filler metal should be used. If matching alloy is not available then the nearest alloy richer in the essential chemistry (Ni, Co, Cr, Mo) should be used. All weld beads should be slightly convex. It is not necessary to use preheating. Surfaces to be welded must be clean and free from oil, paint or crayon marking. The cleaned area should extend at least 2" beyond either side of a welded joint. Gas-Tungsten Arc Welding: DC straight polarity (electrode negative) is recommended. Keep as short an arc length as possible and use care to keep the hot end of filler metal always within the protective atmosphere. Shielded Metal-Arc Welding: Electrodes should be kept in dry storage and if moisture has been picked up the electrodes should be baked at 600 F for one hour to insure dryness. Current settings vary from 60 amps for thin material (0.062" thick) up to 140 amps for material of 1/2" and thicker. It is best to weave the electrode slightly as this alloy weld metal does not tend to spread. Cleaning of slag is done with a wire brush (hand or powered). Complete removal of all slag is very important before successive weld passes and also after final welding. Gas Metal-Arc Welding: Reverse-polarity DC should be used and best results are obtained with the welding gun at 90 degrees to the joint. For Short-Circuiting-Transfer GMAW a typical voltage is 20- 23 with a current of 110-130 amps and a wire feed of 250-275 inches per minute. For Spray-Transfer GMAW voltage of 26 to 33 and current in the range of 175-300 amps with wire feed rate of 200-350 inches per minute are typical. Submerged-Arc Welding: Matching filler metal, the same as for GMAW, should be used. DC current with either reverse or straight polarity may be used. Convex weld beads are preferred.
    Super Alloys Rene 41 Heat Treatment The alloy is age-hardenable (see under "Aging") and can be annealed at 1900 F followed by air cooling.
    Super Alloys Rene 41 Forging Forging is done in the range of 2050 F to 1700 F. Final reductions of 20% for open die work and 10% for closed die are desired to maintain proper grain structure and finishing temperatures should be in the 1750 F - 1700 F range.
    Super Alloys Rene 41 Hot Working Hot working may be done in the temperature range of 2050 F to 1650 F. It is important to reheat the alloy if hot working temperatures fall below 1650 F.
    Super Alloys Rene 41 Cold Working Cold forming may be done using standard tooling although plain carbon tool steels are not recommended for forming as they tend to produce galling. Soft die materials (bronze, zinc alloys, etc.) minimize galling and produce good finishes, but die life is somewhat short. For long production runs the alloy tool steels ( D-2, D-3) and high-speed steels (T-1, M-2, M-10) give good results especially if hard chromium plated to reduce galling. Tooling should be such as to allow for liberal clearances and radii. Heavy duty lubricants should be used to minimize galling in all forming operations. Bending of sheet or plate through 180 degrees is generally limited to a bend radius of 1 T for material up to 1/8" thick and 2 T for material thicker than 1/8".
    Super Alloys Rene 41 Annealing Annealing may be done at 1900 F followed by rapid air cooling.
    Super Alloys Rene 41 Aging Two slightly different aging heat treatments are available. 1. 1800 F anneal and age at 1325 F for 8 hours, then furnace cool to 1150 F and hold at that temperature for 10 hours, then air cool. This is the optimum treatment for the highest room temperature strength and the best rupture properties. 2. 1925 F anneal and age at 1400 F, furnace cool to 1200 F and hold there for 10 hours, furnace cool to 1200 F and hold for 10 hours, then air cool. This treatment will give the best transverse ductility, especially in heavy sections. However it does tend to promote notch brittleness.
    Super Alloys Rene 41 Hardening Cold work will cause an increase in both hardness and strength. The alloy may also be age-hardened -- see "Heat Treat".
    Other Mechanical Props Impact strength values for Charpy V-Notch: At room temperatures: 20.5 ft. lbs. At minus 320 F: 19 ft. lbs.

  • Super Alloys Rene 41 Physical Data


    Density (lb / cu. in.) 0.29
    Specific Gravity 7.98
    Specific Heat (Btu/lb/Deg F - [32-212 Deg F]) 0.104
    Electrical Resistivity (microhm-cm (at 68 Deg F)) 753
    Melting Point (Deg F) 2420
    Poissons Ratio 0.284
    Thermal Conductivity 77
    Mean Coeff Thermal Expansion 7.3
    Magnetic Permeability 1.001
    Modulus of Elasticity Tension 29

  • Searches related to Super Alloys Rene 41


    Super Alloys Rene 41 Sheets & Plates Super Alloys Rene 41 Olets
    Super Alloys Rene 41 Globe valves Super Alloys Rene 41 Strips & Coils
    Super Alloys Rene 41 Nippolets Super Alloys Rene 41 Check valves
    Super Alloys Rene 41 Round bars Super Alloys Rene 41 Sockolet
    Super Alloys Rene 41 Ball valves Super Alloys Rene 41 Hexagonal Bars
    Super Alloys Rene 41 Threadolet Super Alloys Rene 41 forged valves
    Super Alloys Rene 41 Flat bars Super Alloys Rene 41 Union fittings
    Super Alloys Rene 41 Butterfly valves Super Alloys Rene 41 forged bars
    Super Alloys Rene 41 Socket weld fittings Super Alloys Rene 41 needle valves
    Super Alloys Rene 41 Seamless Pipes Super Alloys Rene 41 Forged Threaded fittings
    Super Alloys Rene 41 Plug valves Super Alloys Rene 41 Welded pipes
    Super Alloys Rene 41 Plugs and Bushings Super Alloys Rene 41 Bleed valves
    Super Alloys Rene 41 Seamless Tubes Super Alloys Rene 41 Weld neck flanges
    Super Alloys Rene 41 custom valves Super Alloys Rene 41 Welded tubes
    Super Alloys Rene 41 slip on flanges Super Alloys Rene 41 Wires
    Super Alloys Rene 41 Large diameter pipe & Tube Super Alloys Rene 41 Blind flanges
    Super Alloys Rene 41 Reducer Super Alloys Rene 41 flanges
    Super Alloys Rene 41 Lap joint flanges Super Alloys Rene 41 Cap
    Super Alloys Rene 41 Valves Super Alloys Rene 41 Threaded flanges
    Super Alloys Rene 41 Concentric reducer Super Alloys Rene 41 forged fittings
    Super Alloys Rene 41 large diameter flanges Super Alloys Rene 41 Eccentric reducer
    Super Alloys Rene 41 Buttweld fittings Super Alloys Rene 41 custom flanges
    Super Alloys Rene 41 stubend Super Alloys Rene 41 Forged components
    Super Alloys Rene 41 forged flanges Super Alloys Rene 41 blank flanges
    Super Alloys Rene 41 CNC components Super Alloys Rene 41 buttweld flanges
    Super Alloys Rene 41 spectacle flanges Super Alloys Rene 41 elbow & tee
    Super Alloys Rene 41 plate flanges Super Alloys Rene 41 welded flanges
    Super Alloys Rene 41 gate valves Super Alloys Rene 41 bends
    Super Alloys Rene 41 Nipples

  • METALMINISTRY INC. supply Super Alloys Rene 41 strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves in Agartala ,Agra, Agra Rampur, Ahmedabad, Aizawl, Ajmer, Aligarh, Allahabad, Alwar, Amaravati, Ambala, Ambattur, Ambernath, Amravati, Amritsar, Aurangabad, Bangalore, Bareilly, Belgaum, Bhagalpur, Bhavnagar, Bhilai, Bhiwandi, Bhopal, Bhubaneswar, Bidhannagar, Biharsharif,Bikaner, Bilaspur, Bokaro, Chandigarh, Chennai, Chittoor, Coimbatore, Cuttack, Dahod, Davanegere, Dehradun, Delhi, Dhanbad, Dharamsala, Dindigul, Diu, Durgapur, Erode, Faridabad, Fatehpur, Gandhidham, Gandhinagar, Ghaziabad, Greater Hyderabad, Greater Mumbai, Greater Warangal, Gurgaon, Guwahati, Gwalior, Haldia, Howrah , Hubballi-Dharwad, Hyderabad, Imphal, Indore, Jabalpur, Jaipur, Jalandhar, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kakinada, Kalyan-Dombivali,Kanpur, Karnal , Kavaratti, Kochi, Kohima, Kolhapur, Kolkata, Kota, Lucknow, Ludhiana, Madurai, Mehsana, Mangalore, Mangaluru, Mira-Bhayandar , Moradabad, Morbi, Mumbai, Muzaffarpur, Mysore, Nagpur, Namchi, Nasik, Navi Mumbai, NDMC, Nellore,New Delhi, New Town Kolkata, Noida, Oulgaret, Pali, Panaji, Panipat, Panvel, Pasighat, Patiala, Patna, Pimpri-Chinchwad, Port Blair, Puducherry, Pune, Raipur, Rajkot, Ranchi, Raurkela Industrial Township, Rourkela, Sagar, Salem, Satna, Secunderabad, Shaharanpur, Shillong, Siliguri, Silvassa, Solapur, Srinagar, Surat, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirapalli, Tirunelveli, Tirupur, Tumkur, Udaipur, Ujjain, Ulhasnagar, Vadodara, Vapi, Varanasi, Vasai-Virar, Vellore , Vishakhapatnam.

    METALMINISTRY INC. Exports Super Alloys Rene 41 Strips & Coils to United States of America, Russia, United Kingdom, Kuwait, Qatar, Oman, UAE, Nigeria, Ethiosia, Egypt, Tanzania, Uganda, Algeria, Sudan, Morocco, Angola, Mozambique, Ghana, Cameroon, Cote D`lvoire, Niger, Burkina Faso, Mali, Malawi, Zambia, Senegal, Chad, Somalia, Zimbabwe, Guinea, Rwanda, Benin, Brundi, Tunisia, South Sudan, Togo, Sierra Leone, Libya, Congo, Liberia, Central African Republic, Mauritania, Eritrea, Namibia, Gambia, Botswana, Gabon, Lesotho, Guinea-Bissau, Mauritius, Eswatini, Djibouti, Comoros, Cabo Verde, Seychelles, Reunion, Western Sahara, Mayotte, Saint Helena, Afghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, Cyprus, East Timor, Cyprus, Georgia, Indonesia, Iran, Iraq, Israel, Japan, Kazakhstan, Jordan, Kyrgyzstan, Lebanon, Malaysia, Maldives, Mongolia, Myanmar, Nepal, North Korea, Palestine, Philippines, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Tajikistan, Thailand, Turkey, Taiwan, Uzbekistan, Vietnam, Yemen, Albania, Andorra, Austria, Belarus, Belgium, Bosnia & Herzegovina, Bulgaria, Croatia, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Moldova, Monaco, Montenegro, Norway, Netherlands, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Ukraine, Vatican City, Antigua & Barbuda, Anguilla, The Bahamas, Barbados, British Virgin Island, Canada, Cayman Island, Costa Rica, Cuba, Dominica, Greenland, Haiti, Jamaica, Martinique, Mexico, Navassa Island, Panama, Puerto Rico, Saint Lucia, Trinidad & Tobago, Argentina, Brazil, Bolivia, Chile, Ecuador, Colombia, Guyana, Paraguay, Peru, Uruguay, Venezuela, Australia, Fiji, Marshall Island, New Zealand, Papua New Guinea, Samoa, Solomon Islands & Tuvalu. .

To buy online, Or get price of Super Alloys Rene 41 Strips & Coils send us an email on enquiry@metalministry.in or Call/WhatsApp on +91-9892171042 for quick quote & response. And Strips & Coils are supplied in Relevant standards as per customer requirements & Mill TC from Indian, USA, South African, Russian, German & European Mills only.