Call on: +91-9892171042

Super Alloys Hastelloy N, AMS 5607, AMS 5771, ASTM B366, ASTM B434, ASTM B573, UNS N10003

Super Alloys


  • Super Alloy HASTELLOY(r) N alloy (TM) is available in strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves.

    Super Alloys Hastelloy N is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened.

  • Super Alloys Hastelloy N Chemical Data


    Aluminum 0.2 - 0.8
    Boron 0.006 max
    Carbon 0.08 max
    Chromium 17 - 21
    Cobalt 1 max
    Copper 0.3 max
    Iron Balance
    Manganese 0.35 max
    Molybdenum 2.8 - 3.3
    Nickel 50 - 55
    Niobium 4.75 - 5.5
    Phosphorus 0.015 max
    Silicon 0.35 max
    Sulphur 0.015 max
    Titanium 0.65 - 1.15
    Principal Design Features This is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened.
    Super Alloys Hastelloy N Applications Applications include gas turbine hot section components and cryogenic storage tanks.
    Super Alloys Hastelloy N Machinability Conventional machining techniques used for iron based alloys may be used. This alloy does work-harden during machining and has higher strength and "gumminess" not typical of steels. Heavy duty machining equipment and tooling should be used to minimize chatter or work-hardening of the alloy ahead of the cutting. Most any commercial coolant may be used in the machining operations. Water-base coolants are preferred for high speed operations such as turning, grinding, or milling. Heavy lubricants work best for drilling, tapping, broaching or boring. Turning: Carbide tools are recommended for turning with a continuous cut. High-speed steel tooling should be used for interrupted cuts and for smooth finishing to close tolerance. Tools should have a positive rake angle. Cutting speeds and feeds are in the following ranges: Drilling: Steady feed rates must be used to avoid work hardening due to dwelling of the drill on the metal. Rigid set-ups are essential with as short a stub drill as feasible. Heavy-duty, high-speed steel drills with a heavy web are recommended. Feeds vary from 0.0007 inch per rev. for holes of less than 1/16" diameter, 0.003 inch per rev. for 1/4" dia., to 0.010 inch per rev. for holes of 7/8"diameter. Slow surface speed, as 8-10 feet/minute, are best for drilling. Milling: To obtain good accuracy and a smooth finish it is essential to have rigid machines and fixtures and sharp cutting tools. High-speed steel cutters such as M-2 or M-10 work best with cutting speeds of 5 to 15 feet per minute and feed of 0.001"-0.004" per cutting tooth. Grinding: The alloy should be wet ground and aluminum oxide wheels or belts are preferred.
    Super Alloys Hastelloy N Forming This alloy has good ductility and may be readily formed by all conventional methods. Because the alloy is stronger than regular steel it requires more powerful equipment to accomplish forming. Heavy-duty lubricants should be used during cold forming. It is essential to thoroughly clean the part of all traces of lubricant after forming as embrittlement of the alloy may occur at high temperatures if lubricant is left on.
    Super Alloys Hastelloy N Welding The commonly used welding methods work well with this alloy. Matching alloy filler metal should be used. If matching alloy is not available then the nearest alloy richer in the essential chemistry (Ni, Co, Cr, Mo) should be used. All weld beads should be slightly convex. It is not necessary to use preheating. Surfaces to be welded must be clean and free from oil, paint or crayon marking. The cleaned area should extend at least 2" beyond either side of a welded joint. Gas-Tungsten Arc Welding: DC straight polarity (electrode negative) is recommended. Keep as short an arc length as possible and use care to keep the hot end of filler metal always within the protective atmosphere. Shielded Metal-Arc Welding: Electrodes should be kept in dry storage and if moisture has been picked up the electrodes should be baked at 600 F for one hour to insure dryness. Current settings vary from 60 amps for thin material (0.062" thick) up to 140 amps for material of 1/2" and thicker. It is best to weave the electrode slightly as this alloy weld metal does not tend to spread. Cleaning of slag is done with a wire brush (hand or powered). Complete removal of all slag is very important before successive weld passes and also after final welding. Gas Metal-Arc Welding: Reverse-polarity DC should be used and best results are obtained with the welding gun at 90 degrees to the joint. For Short-Circuiting-Transfer GMAW a typical voltage is 20- 23 with a current of 110-130 amps and a wire feed of 250-275 inches per minute. For Spray-Transfer GMAW voltage of 26 to 33 and current in the range of 175-300 amps with wire feed rate of 200-350 inches per minute are typical. Submerged-Arc Welding: Matching filler metal, the same as for GMAW, should be used. DC current with either reverse or straight polarity may be used. Convex weld beads are preferred.
    Super Alloys Hastelloy N Heat Treatment The alloy is age-hardenable (see under "Aging") and can be annealed at 1900 F followed by air cooling.
    Super Alloys Hastelloy N Forging Forging is done in the range of 2050 F to 1700 F. Final reductions of 20% for open die work and 10% for closed die are desired to maintain proper grain structure and finishing temperatures should be in the 1750 F - 1700 F range.
    Super Alloys Hastelloy N Hot Working Hot working may be done in the temperature range of 2050 F to 1650 F. It is important to reheat the alloy if hot working temperatures fall below 1650 F.
    Super Alloys Hastelloy N Cold Working Cold forming may be done using standard tooling although plain carbon tool steels are not recommended for forming as they tend to produce galling. Soft die materials (bronze, zinc alloys, etc.) minimize galling and produce good finishes, but die life is somewhat short. For long production runs the alloy tool steels ( D-2, D-3) and high-speed steels (T-1, M-2, M-10) give good results especially if hard chromium plated to reduce galling. Tooling should be such as to allow for liberal clearances and radii. Heavy duty lubricants should be used to minimize galling in all forming operations. Bending of sheet or plate through 180 degrees is generally limited to a bend radius of 1 T for material up to 1/8" thick and 2 T for material thicker than 1/8".
    Super Alloys Hastelloy N Annealing Annealing may be done at 1900 F followed by rapid air cooling.
    Super Alloys Hastelloy N Aging Two slightly different aging heat treatments are available. 1. 1800 F anneal and age at 1325 F for 8 hours, then furnace cool to 1150 F and hold at that temperature for 10 hours, then air cool. This is the optimum treatment for the highest room temperature strength and the best rupture properties. 2. 1925 F anneal and age at 1400 F, furnace cool to 1200 F and hold there for 10 hours, furnace cool to 1200 F and hold for 10 hours, then air cool. This treatment will give the best transverse ductility, especially in heavy sections. However it does tend to promote notch brittleness.
    Super Alloys Hastelloy N Hardening Cold work will cause an increase in both hardness and strength. The alloy may also be age-hardened -- see "Heat Treat".
    Other Mechanical Props Impact strength values for Charpy V-Notch: At room temperatures: 20.5 ft. lbs. At minus 320 F: 19 ft. lbs.

  • Super Alloys Hastelloy N Physical Data


    Density (lb / cu. in.) 0.29
    Specific Gravity 7.98
    Specific Heat (Btu/lb/Deg F - [32-212 Deg F]) 0.104
    Electrical Resistivity (microhm-cm (at 68 Deg F)) 753
    Melting Point (Deg F) 2420
    Poissons Ratio 0.284
    Thermal Conductivity 77
    Mean Coeff Thermal Expansion 7.3
    Magnetic Permeability 1.001
    Modulus of Elasticity Tension 29

  • Searches related to Super Alloys Hastelloy N


    Super Alloys Hastelloy N Sheets & Plates Super Alloys Hastelloy N Olets
    Super Alloys Hastelloy N Globe valves Super Alloys Hastelloy N Strips & Coils
    Super Alloys Hastelloy N Nippolets Super Alloys Hastelloy N Check valves
    Super Alloys Hastelloy N Round bars Super Alloys Hastelloy N Sockolet
    Super Alloys Hastelloy N Ball valves Super Alloys Hastelloy N Hexagonal Bars
    Super Alloys Hastelloy N Threadolet Super Alloys Hastelloy N forged valves
    Super Alloys Hastelloy N Flat bars Super Alloys Hastelloy N Union fittings
    Super Alloys Hastelloy N Butterfly valves Super Alloys Hastelloy N forged bars
    Super Alloys Hastelloy N Socket weld fittings Super Alloys Hastelloy N needle valves
    Super Alloys Hastelloy N Seamless Pipes Super Alloys Hastelloy N Forged Threaded fittings
    Super Alloys Hastelloy N Plug valves Super Alloys Hastelloy N Welded pipes
    Super Alloys Hastelloy N Plugs and Bushings Super Alloys Hastelloy N Bleed valves
    Super Alloys Hastelloy N Seamless Tubes Super Alloys Hastelloy N Weld neck flanges
    Super Alloys Hastelloy N custom valves Super Alloys Hastelloy N Welded tubes
    Super Alloys Hastelloy N slip on flanges Super Alloys Hastelloy N Wires
    Super Alloys Hastelloy N Large diameter pipe & Tube Super Alloys Hastelloy N Blind flanges
    Super Alloys Hastelloy N Reducer Super Alloys Hastelloy N flanges
    Super Alloys Hastelloy N Lap joint flanges Super Alloys Hastelloy N Cap
    Super Alloys Hastelloy N Valves Super Alloys Hastelloy N Threaded flanges
    Super Alloys Hastelloy N Concentric reducer Super Alloys Hastelloy N forged fittings
    Super Alloys Hastelloy N large diameter flanges Super Alloys Hastelloy N Eccentric reducer
    Super Alloys Hastelloy N Buttweld fittings Super Alloys Hastelloy N custom flanges
    Super Alloys Hastelloy N stubend Super Alloys Hastelloy N Forged components
    Super Alloys Hastelloy N forged flanges Super Alloys Hastelloy N blank flanges
    Super Alloys Hastelloy N CNC components Super Alloys Hastelloy N buttweld flanges
    Super Alloys Hastelloy N spectacle flanges Super Alloys Hastelloy N elbow & tee
    Super Alloys Hastelloy N plate flanges Super Alloys Hastelloy N welded flanges
    Super Alloys Hastelloy N gate valves Super Alloys Hastelloy N bends
    Super Alloys Hastelloy N Nipples

  • METALMINISTRY INC. supply Super Alloys Hastelloy N strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves in Agartala ,Agra, Agra Rampur, Ahmedabad, Aizawl, Ajmer, Aligarh, Allahabad, Alwar, Amaravati, Ambala, Ambattur, Ambernath, Amravati, Amritsar, Aurangabad, Bangalore, Bareilly, Belgaum, Bhagalpur, Bhavnagar, Bhilai, Bhiwandi, Bhopal, Bhubaneswar, Bidhannagar, Biharsharif,Bikaner, Bilaspur, Bokaro, Chandigarh, Chennai, Chittoor, Coimbatore, Cuttack, Dahod, Davanegere, Dehradun, Delhi, Dhanbad, Dharamsala, Dindigul, Diu, Durgapur, Erode, Faridabad, Fatehpur, Gandhidham, Gandhinagar, Ghaziabad, Greater Hyderabad, Greater Mumbai, Greater Warangal, Gurgaon, Guwahati, Gwalior, Haldia, Howrah , Hubballi-Dharwad, Hyderabad, Imphal, Indore, Jabalpur, Jaipur, Jalandhar, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kakinada, Kalyan-Dombivali,Kanpur, Karnal , Kavaratti, Kochi, Kohima, Kolhapur, Kolkata, Kota, Lucknow, Ludhiana, Madurai, Mehsana, Mangalore, Mangaluru, Mira-Bhayandar , Moradabad, Morbi, Mumbai, Muzaffarpur, Mysore, Nagpur, Namchi, Nasik, Navi Mumbai, NDMC, Nellore,New Delhi, New Town Kolkata, Noida, Oulgaret, Pali, Panaji, Panipat, Panvel, Pasighat, Patiala, Patna, Pimpri-Chinchwad, Port Blair, Puducherry, Pune, Raipur, Rajkot, Ranchi, Raurkela Industrial Township, Rourkela, Sagar, Salem, Satna, Secunderabad, Shaharanpur, Shillong, Siliguri, Silvassa, Solapur, Srinagar, Surat, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirapalli, Tirunelveli, Tirupur, Tumkur, Udaipur, Ujjain, Ulhasnagar, Vadodara, Vapi, Varanasi, Vasai-Virar, Vellore , Vishakhapatnam.

    METALMINISTRY INC. Exports Super Alloys Hastelloy N Strips & Coils to United States of America, Russia, United Kingdom, Kuwait, Qatar, Oman, UAE, Nigeria, Ethiosia, Egypt, Tanzania, Uganda, Algeria, Sudan, Morocco, Angola, Mozambique, Ghana, Cameroon, Cote D`lvoire, Niger, Burkina Faso, Mali, Malawi, Zambia, Senegal, Chad, Somalia, Zimbabwe, Guinea, Rwanda, Benin, Brundi, Tunisia, South Sudan, Togo, Sierra Leone, Libya, Congo, Liberia, Central African Republic, Mauritania, Eritrea, Namibia, Gambia, Botswana, Gabon, Lesotho, Guinea-Bissau, Mauritius, Eswatini, Djibouti, Comoros, Cabo Verde, Seychelles, Reunion, Western Sahara, Mayotte, Saint Helena, Afghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, Cyprus, East Timor, Cyprus, Georgia, Indonesia, Iran, Iraq, Israel, Japan, Kazakhstan, Jordan, Kyrgyzstan, Lebanon, Malaysia, Maldives, Mongolia, Myanmar, Nepal, North Korea, Palestine, Philippines, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Tajikistan, Thailand, Turkey, Taiwan, Uzbekistan, Vietnam, Yemen, Albania, Andorra, Austria, Belarus, Belgium, Bosnia & Herzegovina, Bulgaria, Croatia, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Moldova, Monaco, Montenegro, Norway, Netherlands, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Ukraine, Vatican City, Antigua & Barbuda, Anguilla, The Bahamas, Barbados, British Virgin Island, Canada, Cayman Island, Costa Rica, Cuba, Dominica, Greenland, Haiti, Jamaica, Martinique, Mexico, Navassa Island, Panama, Puerto Rico, Saint Lucia, Trinidad & Tobago, Argentina, Brazil, Bolivia, Chile, Ecuador, Colombia, Guyana, Paraguay, Peru, Uruguay, Venezuela, Australia, Fiji, Marshall Island, New Zealand, Papua New Guinea, Samoa, Solomon Islands & Tuvalu. .

To buy online, Or get price of Super Alloys Hastelloy N Strips & Coils send us an email on enquiry@metalministry.in or Call/WhatsApp on +91-9892171042 for quick quote & response. And Strips & Coils are supplied in Relevant standards as per customer requirements & Mill TC from Indian, USA, South African, Russian, German & European Mills only.