Super Alloys Nitronic 32, ASTM A580 (XM-28) UNS S24100
Super Alloys
- A-286
- Alloy N-155 (Multimet)
- Alloy Haynes 214
- Alloy Haynes 242
- Alloy 25 (L-605)
- Alloy Ferralium 255
- Alloy 301
- Alloy 42 (Ni/Fe)
- Alloy 42-6 (Ni/Fe)
- Alloy 49 (Ni/Fe)
- Alloy 52 (Ni/Fe)
- Astroloy
- D-979
- Discalloy
- FeCrAlY
- Ferro-TiC
- Hastelloy B2
- Hastelloy C22
- Hastelloy C276
- Hastelloy C4
- Hastelloy G
- Hastelloy G3
- Hastelloy G30
- Hastelloy G50
- Hastelloy H9M
- Hastelloy N
- Hastelloy S
- Hastelloy W
- Hastelloy X
- Haynes 188
- Haynes 230
- Haynes 556
- Haynes HR-120
- Haynes HR-160
- Hiperco 50
- Hy Mu 80
- Incoloy 800
- Incoloy 800H
- Incoloy 800HT
- Incoloy 825
- Incoloy 907
- Incoloy 909
- Incoloy 925
- Incoloy DS
- Incoloy MA956
- Inconel 600
- Inconel 601
- Inconel 617
- Inconel 625
- Inconel 690
- Inconel 706
- Inconel 718
- Inconel 722
- Inconel 751
- Inconel MA 954
- Inconel X750
- Invar
- Kovar
- MAR M 918
- Memory Alloy
- Monel 400
- Monel 401
- Monel 404
- Monel 502
- Monel K500
- Monel R405
- Nickel Berrylium Alloy 360
- Nichrome
- Nichrome V
- Nickel 200
- Nickel 201
- Nickel 205
- Nickel 211
- Nickel 220
- Nickel 230
- Nickel 233
- Nickel 270
- Nimonic 101
- Nimonic 105
- Nimonic 115
- Nimonic 80A
- Nimonic 81A
- Nimonic 86
- Nimonic 90
- Nimonic AP1
- Nimonic PE11
- Nimonic PE16
- Nimonic PK33
- Nitronic 30
- Nitronic 32
- Nitronic 33
- Nitronic 50
- Nitronic 60
- Permanickel 300
- RA 85H
- Rene 41
- Rene 95
- Super Invar
- Vanadium Permendur
-
Super Alloys Nitronic 32 is available in strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves.
Super Alloys Nitronic 32 is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened.
-
Super Alloys Nitronic 32 Chemical Data
Aluminum 0.2 - 0.8 Boron 0.006 max Carbon 0.08 max Chromium 17 - 21 Cobalt 1 max Copper 0.3 max Iron Balance Manganese 0.35 max Molybdenum 2.8 - 3.3 Nickel 50 - 55 Niobium 4.75 - 5.5 Phosphorus 0.015 max Silicon 0.35 max Sulphur 0.015 max Titanium 0.65 - 1.15
Principal Design Features This is a high-strength, high-temperature resistant and corrosion resistant nickel-chromium alloy. It is suitable for use at cryogenic temperatures and also for use in air up to 1300 F. The alloy is readily worked and can be age-hardened. Super Alloys Nitronic 32 Applications Applications include gas turbine hot section components and cryogenic storage tanks. Super Alloys Nitronic 32 Machinability Conventional machining techniques used for iron based alloys may be used. This alloy does work-harden during machining and has higher strength and "gumminess" not typical of steels. Heavy duty machining equipment and tooling should be used to minimize chatter or work-hardening of the alloy ahead of the cutting. Most any commercial coolant may be used in the machining operations. Water-base coolants are preferred for high speed operations such as turning, grinding, or milling. Heavy lubricants work best for drilling, tapping, broaching or boring. Turning: Carbide tools are recommended for turning with a continuous cut. High-speed steel tooling should be used for interrupted cuts and for smooth finishing to close tolerance. Tools should have a positive rake angle. Cutting speeds and feeds are in the following ranges: Drilling: Steady feed rates must be used to avoid work hardening due to dwelling of the drill on the metal. Rigid set-ups are essential with as short a stub drill as feasible. Heavy-duty, high-speed steel drills with a heavy web are recommended. Feeds vary from 0.0007 inch per rev. for holes of less than 1/16" diameter, 0.003 inch per rev. for 1/4" dia., to 0.010 inch per rev. for holes of 7/8"diameter. Slow surface speed, as 8-10 feet/minute, are best for drilling. Milling: To obtain good accuracy and a smooth finish it is essential to have rigid machines and fixtures and sharp cutting tools. High-speed steel cutters such as M-2 or M-10 work best with cutting speeds of 5 to 15 feet per minute and feed of 0.001"-0.004" per cutting tooth. Grinding: The alloy should be wet ground and aluminum oxide wheels or belts are preferred. Super Alloys Nitronic 32 Forming This alloy has good ductility and may be readily formed by all conventional methods. Because the alloy is stronger than regular steel it requires more powerful equipment to accomplish forming. Heavy-duty lubricants should be used during cold forming. It is essential to thoroughly clean the part of all traces of lubricant after forming as embrittlement of the alloy may occur at high temperatures if lubricant is left on. Super Alloys Nitronic 32 Welding The commonly used welding methods work well with this alloy. Matching alloy filler metal should be used. If matching alloy is not available then the nearest alloy richer in the essential chemistry (Ni, Co, Cr, Mo) should be used. All weld beads should be slightly convex. It is not necessary to use preheating. Surfaces to be welded must be clean and free from oil, paint or crayon marking. The cleaned area should extend at least 2" beyond either side of a welded joint. Gas-Tungsten Arc Welding: DC straight polarity (electrode negative) is recommended. Keep as short an arc length as possible and use care to keep the hot end of filler metal always within the protective atmosphere. Shielded Metal-Arc Welding: Electrodes should be kept in dry storage and if moisture has been picked up the electrodes should be baked at 600 F for one hour to insure dryness. Current settings vary from 60 amps for thin material (0.062" thick) up to 140 amps for material of 1/2" and thicker. It is best to weave the electrode slightly as this alloy weld metal does not tend to spread. Cleaning of slag is done with a wire brush (hand or powered). Complete removal of all slag is very important before successive weld passes and also after final welding. Gas Metal-Arc Welding: Reverse-polarity DC should be used and best results are obtained with the welding gun at 90 degrees to the joint. For Short-Circuiting-Transfer GMAW a typical voltage is 20- 23 with a current of 110-130 amps and a wire feed of 250-275 inches per minute. For Spray-Transfer GMAW voltage of 26 to 33 and current in the range of 175-300 amps with wire feed rate of 200-350 inches per minute are typical. Submerged-Arc Welding: Matching filler metal, the same as for GMAW, should be used. DC current with either reverse or straight polarity may be used. Convex weld beads are preferred. Super Alloys Nitronic 32 Heat Treatment The alloy is age-hardenable (see under "Aging") and can be annealed at 1900 F followed by air cooling. Super Alloys Nitronic 32 Forging Forging is done in the range of 2050 F to 1700 F. Final reductions of 20% for open die work and 10% for closed die are desired to maintain proper grain structure and finishing temperatures should be in the 1750 F - 1700 F range. Super Alloys Nitronic 32 Hot Working Hot working may be done in the temperature range of 2050 F to 1650 F. It is important to reheat the alloy if hot working temperatures fall below 1650 F. Super Alloys Nitronic 32 Cold Working Cold forming may be done using standard tooling although plain carbon tool steels are not recommended for forming as they tend to produce galling. Soft die materials (bronze, zinc alloys, etc.) minimize galling and produce good finishes, but die life is somewhat short. For long production runs the alloy tool steels ( D-2, D-3) and high-speed steels (T-1, M-2, M-10) give good results especially if hard chromium plated to reduce galling. Tooling should be such as to allow for liberal clearances and radii. Heavy duty lubricants should be used to minimize galling in all forming operations. Bending of sheet or plate through 180 degrees is generally limited to a bend radius of 1 T for material up to 1/8" thick and 2 T for material thicker than 1/8". Super Alloys Nitronic 32 Annealing Annealing may be done at 1900 F followed by rapid air cooling. Super Alloys Nitronic 32 Aging Two slightly different aging heat treatments are available. 1. 1800 F anneal and age at 1325 F for 8 hours, then furnace cool to 1150 F and hold at that temperature for 10 hours, then air cool. This is the optimum treatment for the highest room temperature strength and the best rupture properties. 2. 1925 F anneal and age at 1400 F, furnace cool to 1200 F and hold there for 10 hours, furnace cool to 1200 F and hold for 10 hours, then air cool. This treatment will give the best transverse ductility, especially in heavy sections. However it does tend to promote notch brittleness. Super Alloys Nitronic 32 Hardening Cold work will cause an increase in both hardness and strength. The alloy may also be age-hardened -- see "Heat Treat". Other Mechanical Props Impact strength values for Charpy V-Notch: At room temperatures: 20.5 ft. lbs. At minus 320 F: 19 ft. lbs. -
Super Alloys Nitronic 32 Physical Data
Density (lb / cu. in.) 0.29 Specific Gravity 7.98 Specific Heat (Btu/lb/Deg F - [32-212 Deg F]) 0.104 Electrical Resistivity (microhm-cm (at 68 Deg F)) 753 Melting Point (Deg F) 2420 Poissons Ratio 0.284 Thermal Conductivity 77 Mean Coeff Thermal Expansion 7.3 Magnetic Permeability 1.001 Modulus of Elasticity Tension 29 -
Searches related to Super Alloys Nitronic 32
Super Alloys Nitronic 32 Sheets & Plates Super Alloys Nitronic 32 Olets Super Alloys Nitronic 32 Globe valves Super Alloys Nitronic 32 Strips & Coils Super Alloys Nitronic 32 Nippolets Super Alloys Nitronic 32 Check valves Super Alloys Nitronic 32 Round bars Super Alloys Nitronic 32 Sockolet Super Alloys Nitronic 32 Ball valves Super Alloys Nitronic 32 Hexagonal Bars Super Alloys Nitronic 32 Threadolet Super Alloys Nitronic 32 forged valves Super Alloys Nitronic 32 Flat bars Super Alloys Nitronic 32 Union fittings Super Alloys Nitronic 32 Butterfly valves Super Alloys Nitronic 32 forged bars Super Alloys Nitronic 32 Socket weld fittings Super Alloys Nitronic 32 needle valves Super Alloys Nitronic 32 Seamless Pipes Super Alloys Nitronic 32 Forged Threaded fittings Super Alloys Nitronic 32 Plug valves Super Alloys Nitronic 32 Welded pipes Super Alloys Nitronic 32 Plugs and Bushings Super Alloys Nitronic 32 Bleed valves Super Alloys Nitronic 32 Seamless Tubes Super Alloys Nitronic 32 Weld neck flanges Super Alloys Nitronic 32 custom valves Super Alloys Nitronic 32 Welded tubes Super Alloys Nitronic 32 slip on flanges Super Alloys Nitronic 32 Wires Super Alloys Nitronic 32 Large diameter pipe & Tube Super Alloys Nitronic 32 Blind flanges Super Alloys Nitronic 32 Reducer Super Alloys Nitronic 32 flanges Super Alloys Nitronic 32 Lap joint flanges Super Alloys Nitronic 32 Cap Super Alloys Nitronic 32 Valves Super Alloys Nitronic 32 Threaded flanges Super Alloys Nitronic 32 Concentric reducer Super Alloys Nitronic 32 forged fittings Super Alloys Nitronic 32 large diameter flanges Super Alloys Nitronic 32 Eccentric reducer Super Alloys Nitronic 32 Buttweld fittings Super Alloys Nitronic 32 custom flanges Super Alloys Nitronic 32 stubend Super Alloys Nitronic 32 Forged components Super Alloys Nitronic 32 forged flanges Super Alloys Nitronic 32 blank flanges Super Alloys Nitronic 32 CNC components Super Alloys Nitronic 32 buttweld flanges Super Alloys Nitronic 32 spectacle flanges Super Alloys Nitronic 32 elbow & tee Super Alloys Nitronic 32 plate flanges Super Alloys Nitronic 32 welded flanges Super Alloys Nitronic 32 gate valves Super Alloys Nitronic 32 bends Super Alloys Nitronic 32 Nipples -
METALMINISTRY INC. supply Super Alloys Nitronic 32 strips, sheets, plates, round and square bars, seamless and welded pipes & tubes, Forged & buttweld Fittings, flanges, fastener, flat rolled bars, Wire & valves in Agartala ,Agra, Agra Rampur, Ahmedabad, Aizawl, Ajmer, Aligarh, Allahabad, Alwar, Amaravati, Ambala, Ambattur, Ambernath, Amravati, Amritsar, Aurangabad, Bangalore, Bareilly, Belgaum, Bhagalpur, Bhavnagar, Bhilai, Bhiwandi, Bhopal, Bhubaneswar, Bidhannagar, Biharsharif,Bikaner, Bilaspur, Bokaro, Chandigarh, Chennai, Chittoor, Coimbatore, Cuttack, Dahod, Davanegere, Dehradun, Delhi, Dhanbad, Dharamsala, Dindigul, Diu, Durgapur, Erode, Faridabad, Fatehpur, Gandhidham, Gandhinagar, Ghaziabad, Greater Hyderabad, Greater Mumbai, Greater Warangal, Gurgaon, Guwahati, Gwalior, Haldia, Howrah , Hubballi-Dharwad, Hyderabad, Imphal, Indore, Jabalpur, Jaipur, Jalandhar, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kakinada, Kalyan-Dombivali,Kanpur, Karnal , Kavaratti, Kochi, Kohima, Kolhapur, Kolkata, Kota, Lucknow, Ludhiana, Madurai, Mehsana, Mangalore, Mangaluru, Mira-Bhayandar , Moradabad, Morbi, Mumbai, Muzaffarpur, Mysore, Nagpur, Namchi, Nasik, Navi Mumbai, NDMC, Nellore,New Delhi, New Town Kolkata, Noida, Oulgaret, Pali, Panaji, Panipat, Panvel, Pasighat, Patiala, Patna, Pimpri-Chinchwad, Port Blair, Puducherry, Pune, Raipur, Rajkot, Ranchi, Raurkela Industrial Township, Rourkela, Sagar, Salem, Satna, Secunderabad, Shaharanpur, Shillong, Siliguri, Silvassa, Solapur, Srinagar, Surat, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirapalli, Tirunelveli, Tirupur, Tumkur, Udaipur, Ujjain, Ulhasnagar, Vadodara, Vapi, Varanasi, Vasai-Virar, Vellore , Vishakhapatnam.
METALMINISTRY INC. Exports Super Alloys Nitronic 32 Strips & Coils to United States of America, Russia, United Kingdom, Kuwait, Qatar, Oman, UAE, Nigeria, Ethiosia, Egypt, Tanzania, Uganda, Algeria, Sudan, Morocco, Angola, Mozambique, Ghana, Cameroon, Cote D`lvoire, Niger, Burkina Faso, Mali, Malawi, Zambia, Senegal, Chad, Somalia, Zimbabwe, Guinea, Rwanda, Benin, Brundi, Tunisia, South Sudan, Togo, Sierra Leone, Libya, Congo, Liberia, Central African Republic, Mauritania, Eritrea, Namibia, Gambia, Botswana, Gabon, Lesotho, Guinea-Bissau, Mauritius, Eswatini, Djibouti, Comoros, Cabo Verde, Seychelles, Reunion, Western Sahara, Mayotte, Saint Helena, Afghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, Cyprus, East Timor, Cyprus, Georgia, Indonesia, Iran, Iraq, Israel, Japan, Kazakhstan, Jordan, Kyrgyzstan, Lebanon, Malaysia, Maldives, Mongolia, Myanmar, Nepal, North Korea, Palestine, Philippines, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Tajikistan, Thailand, Turkey, Taiwan, Uzbekistan, Vietnam, Yemen, Albania, Andorra, Austria, Belarus, Belgium, Bosnia & Herzegovina, Bulgaria, Croatia, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Moldova, Monaco, Montenegro, Norway, Netherlands, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Ukraine, Vatican City, Antigua & Barbuda, Anguilla, The Bahamas, Barbados, British Virgin Island, Canada, Cayman Island, Costa Rica, Cuba, Dominica, Greenland, Haiti, Jamaica, Martinique, Mexico, Navassa Island, Panama, Puerto Rico, Saint Lucia, Trinidad & Tobago, Argentina, Brazil, Bolivia, Chile, Ecuador, Colombia, Guyana, Paraguay, Peru, Uruguay, Venezuela, Australia, Fiji, Marshall Island, New Zealand, Papua New Guinea, Samoa, Solomon Islands & Tuvalu. .
To buy online, Or get price of Super Alloys Nitronic 32 Strips & Coils send us an email on enquiry@metalministry.in or Call/WhatsApp on +91-9892171042 for quick quote & response. And Strips & Coils are supplied in Relevant standards as per customer requirements & Mill TC from Indian, USA, South African, Russian, German & European Mills only.
